Rock and metal mastering loudness: LUFS from 2,227 tracks
How loud rock and metal uploads are before mastering and where they land after. Median LUFS and true peak from 1,897 rock and 330 metal tracks, and what that means for a band's release.
Topic: Mastering loudness by genre
Rock and metal are often mixed hot, and the level you choose for the master is a choice about how much of the band's dynamics you keep. If you are looking for the right LUFS for a rock or metal track, this article gives the numbers first and then a way to decide for your own release. The figures are numbers from 2,227 tracks processed by the mastering engine behind Echoteka in the last six months (aggregate, no personal data): 1,897 rock tracks and 330 metal tracks.
What the numbers show
| Reading | Rock, 1,897 tracks | Metal, 330 tracks |
|---|---|---|
| Median loudness before mastering | −13.9 LUFS | −13.8 LUFS |
| Middle 80% of uploads (10th to 90th percentile) | −16.4 to −8.5 LUFS | −16.3 to −8.4 LUFS |
| Uploads louder than −10 LUFS before mastering | 18% | 16% |
| Median loudness after mastering | −13.9 LUFS | −11.6 LUFS |
| Median true peak after mastering | −1.1 dBTP | −1.0 dBTP |
Before mastering, the two genres look almost the same. Their medians sit within a tenth of a decibel of each other, and the spread is the same. The difference shows up after mastering. The rock median lands at −13.9 LUFS, very close to the −14 LUFS streaming reference. The metal median lands at −11.6 LUFS, about 2.4 LU above it.
These are medians of two separate sets of measurements, before and after. They show where the work starts and where it ends, for each genre. They are not the change for any single track.
To place your own track against these figures, measure the bounce with the same meter. Both genres share the same spread, so the same test applies to either. If the mix reads between −16 and −12 LUFS, it is in the middle of the range, and a master near −14 LUFS is a moderate change. If it reads louder than −10 LUFS, it belongs to the group that made up 16% to 18% of the sample, and the master will bring it down rather than up. If it reads quieter than −16 LUFS, check the mix level first. Then listen to the choruses and the breakdowns separately. A rock track whose choruses are loud and whose verses are quiet is normal. A track that is quiet all the way through needs a gain check before it needs a master.
What the targets mean for a band
Spotify publishes a loudness target of −14 LUFS for integrated loudness. Many streaming services use a similar reference, so a master near that figure is turned down the least on playback. A master louder than that is turned down, and the amount depends on the platform.
The true peak target is at or below −1 dBTP. Guitar-heavy masters often have dense, high transients, and lossy encoding can add overshoot after the master is exported. A margin of one decibel is the common safe choice, and the engine's medians sit right at that margin.
Metal at −11.6 LUFS is a clear example of a trade-off. On a platform that normalizes, a master that loud is turned down by roughly 2 to 3 dB at playback. The band keeps more density in the file itself, but the listener hears a master closer to the rock median. Decide which of those you want before you master. The free streaming penalty calculator shows how much a given master is turned down on each platform.
Checks before you master a rock or metal track
- Measure the mix, not only the master. Read integrated loudness and true peak on the bounce, and note how far the mix is from −14 LUFS. A mix already at −8 LUFS has no dynamic range to give back.
- Solo the bass and the kick. In rock and metal these often carry the true peak. If they hit the ceiling alone, reduce them before the master, or the whole mix will be pushed down to compensate.
- Check the guitars and the vocal at the new level. Heavy limiting can turn distorted guitars into a wall of sound. Listen to a fast riff and to the chorus after mastering.
- Compare with a band you know. Load a recent release from a reference band at a streaming level and listen at matched loudness. It is the quickest test of whether the density you want costs too much.
- Keep the dynamics in the song. A breakdown should still feel quieter than the chorus after mastering. If it does not, the master is too far up.
Common mistakes in rock and metal mastering
- Matching the loudest reference. Metal is often released loud, and it is tempting to match the loudest album in the genre. The platform turn-down makes that extra loudness invisible, and the cost is in the drums and the guitars.
- Mixing too hot to begin with. A mix that is already clipping on the master bus will not be fixed by a master. Leave headroom in the export.
- Losing the breakdowns. Quiet sections are the first thing to disappear under heavy limiting. Check that the song still has contrast between sections.
- Ignoring true peak on the way out. A master at −1.0 dBTP in the DAW can overshoot after encoding. Export the final file and measure it again.
Where to start
Measure the bounce with the free LUFS checker. If it is near −14 LUFS and the true peak is below −1 dBTP, the master is mostly done. If it is louder or quieter, a free AI mastering pass can bring it to a streaming level, and you can compare the before and after readings.
For a practical view of how much dynamics a loud master gives up, read keeping the dynamics in a second version. It describes how to make a louder and a more dynamic version of the same song.
FAQ
What LUFS should a rock master be for Spotify?
Aim for about −14 LUFS integrated, with a true peak at or below −1 dBTP. The rock median after mastering in our measurements was −13.9 LUFS, and the true peak was −1.1 dBTP.
Is it normal for metal to be louder than rock?
In our data, yes. The metal median after mastering was −11.6 LUFS, while the rock median was −13.9 LUFS. The genre sounds dense, and a louder master is a deliberate choice. The platform will still turn it down on playback, so the difference is audible on streaming as a small step down.
How many tracks does this data include?
There are 2,227 tracks in total: 1,897 rock and 330 metal. The metal sample is smaller, so treat its numbers as a guide to the genre, not a rule for every release.
Measure your rock or metal track before you release it
The LUFS checker is free and needs no account. Measure the bounce first, then decide whether it needs a master.
Master a track free