House and big room mastering loudness: what 369 tracks show
How loud house and big room uploads are before mastering and where they land after, with median LUFS and true peak from 369 tracks, and the trade-off between club density and streaming turn-down.
Topic: Mastering loudness by genre
House and big room are close relatives of EDM, and they share the same tension. Club playback rewards density, and streaming platforms turn loud files down. The two genres are also different from each other. House is usually more groove-driven and sits a little lower in level, while big room is built for the main room of a festival and tends to be pushed harder. If you are looking for the right LUFS for a house track, this article gives the figures from the mastering engine behind Echoteka and explains what they mean for a release. The figures are numbers from 369 tracks processed by the mastering engine behind Echoteka in the last six months (aggregate, no personal data). That total is 233 house tracks and 136 big room tracks.
What the numbers show
| Reading | House, 233 tracks | Big room, 136 tracks |
|---|---|---|
| Median loudness before mastering | −13.5 LUFS | −13.4 LUFS |
| Middle 80% of uploads (10th to 90th percentile) | −16.7 to −9.1 LUFS | −16.1 to −8.1 LUFS |
| Uploads louder than −10 LUFS before mastering | 16% | 32% |
| Median loudness after mastering | −10.3 LUFS | −9.2 LUFS |
| Median true peak after mastering | −1.0 dBTP | −1.0 dBTP |
The two genres start at almost the same median, around −13.5 LUFS. The difference shows up in the upper part of the spread. Big room uploads are louder: 32% arrived louder than −10 LUFS, compared with 16% for house, and the top tenth was louder than −8.1 LUFS.
After mastering, house lands at a median of −10.3 LUFS and big room at −9.2 LUFS. Both medians keep the true peak at −1.0 dBTP, so the density comes from the limiting and the level, not from clipping.
These are medians of two separate sets of measurements, before and after mastering. They describe where each sample started and where it ended. They are not the change for any single track.
To place your own track against these figures, measure the bounce with the same meter. If a house track reads between −16 and −12 LUFS, it is in the middle of the range, and a master to about −10 LUFS is a clear step up. If it reads louder than −10 LUFS, it belongs to the group that made up 16% of the house sample, and the master is more about control than level. For big room, a bounce louder than −10 LUFS is common, and the question is how much of that level you want to keep on streaming.
The trade-off, stated plainly
Streaming platforms normalize playback. Spotify publishes a target of −14 LUFS, and many services use a similar reference. A house master at −10.3 LUFS sits about 3.7 LU above that reference, and a big room master at −9.2 LUFS sits about 4.8 LU above. On a service that turns loud tracks down, the median track in each genre will be reduced by roughly that amount, so the level you paid for in the master does not reach the listener in full.
What you keep is density and energy. A louder master has less space between the loud and quiet parts, and the kick, the bass and the lead sit closer to the top of the range. That is what makes the track work on a large system. The trade-off is real, and it is a choice, not a mistake.
Two practical rules help:
- For streaming playlists and home listening, aim near −14 LUFS and keep the true peak at or below −1 dBTP. The track will sound closer to what you intended after the platform's adjustment, and the groove will keep more of its shape.
- For club and DJ use, a louder master is expected. Keep a second version near −14 LUFS for streaming, so the release is not only a loud file that gets turned down.
The true peak rule stays the same for both versions. Keep each file at or below −1 dBTP, because lossy encoding can add overshoot after export.
Checks before you master a house track
- Measure the bounce, not the meter in your DAW. Read integrated loudness and true peak on the file you will send.
- Decide which version you are making. A streaming master and a club master are different targets. Name the files clearly so they do not get mixed up at upload.
- Check the kick and the sub. In house and big room, the kick and the bass share most of the headroom. Solo the low end and read its true peak before mixing it back in.
- Listen for pumping. Heavy compression on the master can make the whole mix duck on every beat. If the groove breathes in a way you did not intend, the master is too far up.
- Check the drop and the breakdown separately. Read the loudness of each section. A big drop that is far louder than the breakdown can be correct, but the breakdown should still hold its energy on playback.
Common mistakes in house and big room mastering
- Chasing festival loudness on a streaming release. A big room master at −9 LUFS will be turned down on most platforms. Keep the club version for the club, and master the streaming version to a level that keeps its dynamics. The free streaming penalty calculator shows how much a given master is turned down on each platform.
- Letting the limiter flatten the hats. Fast hi-hats and percussion are the first elements to lose their edge under heavy limiting. Listen to them after mastering, not only the kick.
- Using the first bounce as the final master. Many house bounces are exported hot. Lower the mix before sending it, so the master has room to work.
- Ignoring true peak after export. A master with a true peak above −1 dBTP can sound clean in the DAW and still overshoot after encoding.
Where to start
Measure the bounce with the free LUFS checker. If you are preparing both a club and a streaming version, measure each one, so you can see how far apart they really are. If a track needs a level pass, a free AI mastering run can bring it to a streaming target, and you can compare the readings before and after.
For a plain guide to how streaming services handle loudness, read the streaming loudness guide. For the EDM view of the same trade-off, read EDM mastering loudness.
FAQ
What LUFS should a house master be for Spotify?
Aim for about −14 LUFS integrated, with a true peak at or below −1 dBTP. That is the reference Spotify publishes. House uploads in our sample were mastered to a median of −10.3 LUFS, so a streaming version will usually sit below the club level you hear in a set.
Is big room mastered too loud for streaming?
It is loud by design. Big room masters often sit near −9 LUFS, which is far above the −14 LUFS reference. On a platform that turns loud tracks down, the extra level is reduced on playback. If the track is meant for streaming as well as the club, keep a version closer to −14 LUFS.
Do I need two masters for a house release?
Not always, but it helps when a track will be played both in clubs and on streaming. One version can serve both if you accept the platform turn-down. Two versions let you keep the club energy and still give the streaming listener a file that sounds right at home.
Measure your house track before you release it
The LUFS checker is free and needs no account. Measure the bounce first, then decide whether it needs a master.
Master a track free