BLOG

EDM mastering loudness: what 1,118 tracks show

EDM uploads arrive louder than most genres and the EDM preset masters them louder again. Median LUFS and true peak from 1,118 tracks, and the trade-off between club density and streaming turn-down.

EDM is the genre where the loudness question has a real trade-off, not just a right answer. Club and DJ playback rewards density, and streaming platforms turn loud files down. Our numbers show both sides. If you are looking for the right LUFS for an EDM track, this article gives the figures from the mastering engine behind Echoteka and explains what they mean for a release. The figures are numbers from 1,118 tracks processed by the mastering engine behind Echoteka in the last six months (aggregate, no personal data).

What the numbers show

Reading EDM, 1,118 tracks
Median loudness before mastering −13.1 LUFS
Middle 80% of uploads (10th to 90th percentile) −16.3 to −5.3 LUFS
Uploads louder than −10 LUFS before mastering 36%
Median loudness after mastering −9.5 LUFS
Median true peak after mastering −1.0 dBTP

EDM uploads are already louder than most genres. More than one in three arrived louder than −10 LUFS, and the top 10% were louder than −5.3 LUFS. The EDM preset then masters the median to −9.5 LUFS, which is well above the −14 LUFS reference used for streaming. The true peak still lands at −1.0 dBTP, so the preset keeps the ceiling and adds density.

These are medians of two separate sets of measurements, before and after. They describe the genre as it reaches the engine, and the level it leaves with. They are not the change for any one track.

To place your own EDM track against these figures, measure the bounce with the same meter. If it reads quieter than −16 LUFS, it is in the bottom tenth of the sample, and an EDM preset will raise it a long way, so decide first whether that is the level you want. If it reads between −13 and −9 LUFS, it is in the middle of the range, and the preset moves it by a moderate amount. If it reads louder than −10 LUFS, it belongs to the group that made up 36% of the sample. For that track, the question is not whether to master it loud, but which version you are making. A club version and a streaming version can both come from the same mix, and the true peak limit is the same for both.

The trade-off, stated plainly

Streaming platforms normalize playback. Spotify publishes a target of −14 LUFS, and many services use a similar reference. A track that masters to −9.5 LUFS sits about 4.5 LU above that reference. On a platform that turns loud tracks down, the median EDM track will be turned down by roughly that amount. The loudness you paid for in the master does not reach the listener on that platform.

What you keep is density. A louder master has less space between the loud and quiet parts, the kick and the synth sit closer to the top of the range, and the track feels heavier in a club. That is why the EDM preset exists. It is a deliberate choice, and it is not a mistake.

Two rules help you decide where your track belongs:

The true peak rule does not change between the two versions. Keep both at or below −1 dBTP, because lossy encoding can add overshoot after the file leaves your hands.

Checks before you master an EDM track

  1. Measure the bounce, not the meter in your DAW. Read integrated loudness and true peak on the exact file you will send.
  2. Decide which version you are making. A streaming master and a club master are different targets. Name the files so you do not confuse them at upload.
  3. Check the sub and the kick. A loud sub-bass often reaches the true peak first. Solo the low end and read its true peak before you mix it into the rest of the track.
  4. Listen for pumping. Heavy compression on the master can make the kick pull the whole mix down on every beat. If the groove breathes in an unwanted way, the master is too far up.
  5. Compare with a streaming-level reference. Load a track you trust at about −14 LUFS and listen at matched level. This shows whether the density you want is worth the turn-down.

Common mistakes in EDM mastering

Where to start

Measure your bounce with the free LUFS checker. If you want a streaming version of a loud track, a free AI mastering pass can bring it to the −14 LUFS reference, and you can keep your club version separate. Measure both files and keep the readings with the project.

For the wider background on the turn-down, read what the loudness penalty on streaming is. If a master clips on export, how to fix clipped audio walks through the causes.

FAQ

Should an EDM track be mastered to −14 LUFS?

For streaming, yes, as a reference. A master near −14 LUFS keeps its dynamics and is not turned down much on most platforms. For club use, a louder master is common. Many EDM releases have both.

Why is the EDM median so loud after mastering?

The genre arrives loud, and the EDM preset is built for density. In our measurements, the median after mastering was −9.5 LUFS, about 4.5 LU above the −14 LUFS streaming reference. That is a deliberate trade-off, not a fault.

Does a loud EDM master sound worse on streaming?

It does not sound worse in a technical sense, but it is turned down on playback, so the extra loudness is lost to the listener. The bigger risk is that heavy limiting flattens the transients, which can make the track feel tired at the same playback level as the rest of the playlist. The free streaming penalty calculator shows how much a given master is turned down on each platform.

Measure your EDM track before you release it

The LUFS checker is free and needs no account. Measure the bounce first, then decide whether it needs a master.

Master a track free