BLOG

Pop mastering loudness: what 1,426 tracks show

Where pop uploads sit before mastering, where they land after, and how loud a pop master should be for streaming. Median LUFS and true peak from 1,426 tracks, with checks to run before release.

Pop sits between the quiet end of the market and the loud end. The vocal is the centre of the mix, the arrangements are dense, and many pop releases are mastered louder than the −14 LUFS reference that streaming services use. If you are looking for the right LUFS for a pop track, this article gives the numbers first and then a method for checking your own file. The figures are numbers from 1,426 tracks processed by the mastering engine behind Echoteka in the last six months (aggregate, no personal data).

What the numbers show

Reading Pop, 1,426 tracks
Median loudness before mastering −14.0 LUFS
Middle 80% of uploads (10th to 90th percentile) −16.4 to −9.8 LUFS
Uploads louder than −10 LUFS before mastering 11%
Median loudness after mastering −12.5 LUFS
Median true peak after mastering −1.1 dBTP

Pop uploads arrive very close to the −14 LUFS reference. The median is −14.0 LUFS, and the middle 80% runs from −16.4 to −9.8 LUFS. One upload in ten was louder than −9.8 LUFS, and 11% were louder than −10 LUFS before any mastering. Those tracks have little room for a limiter to work with, so the job there is control, not more level.

After mastering, the median moves to −12.5 LUFS. That is 1.5 LU above the −14 reference. It is a deliberate choice for a genre where density is part of the sound, and the median true peak of −1.1 dBTP shows the ceiling is still respected.

These are medians of two separate sets of measurements, one before mastering and one after. They describe where pop starts and where it ends. They are not the change for any single track.

To place your own track against these figures, measure the bounce with the same meter. If it reads between −16 and −12 LUFS, it sits in the middle of the pop range, and a master near −12.5 LUFS is a moderate move. If it reads quieter than −16.4 LUFS, it is in the bottom tenth. Check the gain staging and the balance before you master, because a limiter cannot recover a vocal that was never recorded at a usable level. If it reads louder than −10 LUFS, it belongs to the 11% group. In that case, the master should bring the peaks under control, and the true peak reading tells you how much work that will take.

What the targets mean for a pop master

Spotify publishes a loudness target of −14 LUFS, measured as integrated loudness over the whole track. Many streaming services use a similar reference. A track that masters to −12.5 LUFS sits about 1.5 LU above it, and on a service that turns loud tracks down, that extra level is reduced on playback. What you keep is the density in the master file, and the platform takes back part of the level.

On a service that turns loud tracks down, a master close to −14 LUFS keeps more of its dynamics, because less of it is reduced on playback. For a release that will mostly be heard on streaming, aim between −14 and −12 LUFS, and keep the true peak at or below −1 dBTP. For a release that will also be played on a club or radio system, a second version a little louder can be worth making, as long as both files keep the same true peak limit.

The true peak rule does not change with the genre. Keep it at or below −1 dBTP. Lossy encoding, the MP3 and AAC copies that platforms make from your file, can add overshoot between samples, and the one-decibel margin leaves room for that. The pop median after mastering is −1.1 dBTP, which is consistent with that margin.

Checks before you master a pop track

  1. Measure the bounce, not the meter in your DAW. Load the exact file you plan to send and read integrated loudness and true peak. A peak meter alone does not show how loud the track sounds.
  2. Check the vocal peaks. In pop, the lead vocal is usually the loudest and most compressed element. If its peaks are high before mastering, the limiter will have to work harder on the whole mix to get them under control.
  3. Listen to the chorus at the new level. The chorus is where the density is highest. A master that is too loud makes the chorus feel flat compared with the verse, and that is the first sign the level has gone too far.
  4. Keep the bass in check. A heavy kick or sub-bass can set the true peak on its own. Solo the low end and read its peak before you blame the limiter.
  5. Check on a phone speaker and in the car. Two tracks at the same integrated loudness can still sound different on small speakers. The one with clearer vocals usually wins.

Common mistakes in pop mastering

Where to start

Measure the bounce with the free LUFS checker. It shows integrated loudness, short-term loudness and true peak, which are the numbers this article uses. If your track is close to −14 LUFS and the true peak is below −1 dBTP, the master is mostly done, and the work left is listening. If it is far from the reference, a free AI mastering pass can bring it to a streaming level, and you can measure the result to confirm the change.

To see how each service treats a loud file, read the streaming loudness guide. For the wider background on why very loud masters lose on streaming, read the loudness war on streaming in 2026.

FAQ

What LUFS should a pop master be for streaming?

Aim for about −14 LUFS integrated, and no louder than about −12 LUFS if you want the dynamics of the chorus to survive playback. Keep the true peak at or below −1 dBTP. In our measurements, the pop median after mastering was −12.5 LUFS, which shows how the genre is usually handled.

Is it fine to master a pop track louder than −14 LUFS?

It is fine as a creative choice, but the platform will turn the track down on playback, so part of the extra level does not reach the listener. What you keep is the cost: less space between the loud and quiet parts and more risk of distortion on the peaks. Decide on the sound you want, then check the result with the same meter. The free streaming penalty calculator shows how much a given master is turned down on each platform.

Why does my pop master sound smaller than a reference?

Compare integrated loudness first, using the same meter for both files. A reference that is a few decibels louder will sound bigger. If the levels match and your track still sounds smaller, the difference is usually in the vocal balance or the low end, not in the limiter.

Measure your pop track before you release it

The LUFS checker is free and needs no account. Measure the bounce first, then decide whether it needs a master.

Master a track free