Lo-fi mastering loudness: what 110 tracks show
Lo-fi uploads are often quieter than most genres, and the master often stays quiet on purpose. Median LUFS and true peak from 110 tracks, a small sample, and how to decide the level for a lo-fi release.
Topic: Mastering loudness by genre
Lo-fi is a genre where the quiet, soft sound is part of the point, and many producers do not want a master that sits at the same level as hip-hop or EDM. If you are looking for the right LUFS for a lo-fi track, this article gives the numbers from the mastering engine behind Echoteka and a way to decide the level for your own release. The figures are numbers from 110 tracks processed by the mastering engine behind Echoteka in the last six months (aggregate, no personal data). That is a small sample, so read them as a guide, not as a rule.
What the numbers show
| Reading | Lo-fi, 110 tracks |
|---|---|
| Median loudness before mastering | −14.8 LUFS |
| Middle 80% of uploads (10th to 90th percentile) | −20.6 to −8.6 LUFS |
| Uploads louder than −10 LUFS before mastering | 17% |
| Median loudness after mastering | −15.9 LUFS |
| Median true peak after mastering | −2.2 dBTP |
Two things stand out. The lo-fi median before mastering is already quieter than the −14 LUFS reference, and the quiet end of the spread reaches further down than it does for hip-hop or rock. One lo-fi upload in ten was quieter than −20.6 LUFS. The numbers do not show what each quiet track contains, but a soft style with sparse loops and little high-level content would produce readings like these.
The median after mastering is −15.9 LUFS, below the streaming reference. The median true peak is −2.2 dBTP, which leaves more headroom than most genres. Both results fit a style that is meant to sit low and soft. In this sample, the median stays below the −14 LUFS reference.
These are medians of two separate sets of measurements, before and after, from a small number of tracks. They are not the change for any single track.
To place your own lo-fi track against these figures, measure the bounce with the same meter. If it reads between −18 and −13 LUFS, it is in the middle of the range, and the master can stay close to where it is. If it reads quieter than −20.6 LUFS, it is in the bottom tenth of the sample. That may be the right level for a very soft track, but check the noise floor before you raise anything. If it reads louder than −10 LUFS, it is in the group that made up 17% of the sample, and it is more likely to need turning down than raising, which is unusual for this genre. Because the sample is small, use these bands as a rough guide and rely on your ears for the final decision.
What the targets mean for a lo-fi master
Spotify publishes a loudness target of −14 LUFS. A lo-fi track at −15.9 LUFS is about 2 LU quieter than that reference. On a platform that normalizes loud tracks down and does not turn quiet ones up, the track plays at the level you set. Other platforms and playlists may also handle quiet tracks differently, so check the current behavior of each service you use.
The true peak target is at or below −1 dBTP. The lo-fi median sits well below that line, at −2.2 dBTP, so most lo-fi masters have room to spare. Keep that margin. A soft master can still overshoot after encoding if a few transients are louder than the rest.
Lo-fi masters have a different risk from loud genres. The concern is not clipping or squeeze. It is making the track so quiet that it sounds small next to everything else in a playlist, or so quiet that the hiss and tape noise become the loudest thing in the file.
Checks before you master a lo-fi track
- Measure the bounce. Read integrated loudness and true peak on the exact file you will send. For lo-fi, the number is a reference for the sound you want, not a target you must reach.
- Check the noise floor. Tape hiss, vinyl crackle and room noise are often the loudest part of a quiet master once it is raised. Listen with the level set to the streaming reference and check for hiss that becomes distracting.
- Compare with a reference at matched level. Load a lo-fi track you like and listen at the same integrated loudness. This shows whether your track sounds as warm and present as the reference, or simply quieter.
- Check the low end. Lo-fi often has a soft, rolled-off top and a full bottom. Solo the bass and check its true peak before you master the whole track.
- Listen on a phone speaker. Many lo-fi listeners use small speakers and earbuds. A master that sounds full on studio monitors may feel thin on a phone.
Common mistakes in lo-fi mastering
- Mastering to −14 LUFS by default. A standard streaming target is useful, but it can take the air out of a soft track. Choose the level by listening, and check the number afterwards.
- Raising the noise with the master. A quiet recording with heavy noise reduction or a big gain boost in the master brings the hiss up with the music. Fix the noise in the mix before the master.
- Pushing a quiet track into a loud playlist. A lo-fi master at −16 LUFS sits quieter than most songs in a mixed playlist. That can be the intent, but do not let it happen by accident.
- Judging a soft master on a loud system. A quiet master can sound flat on large speakers and fine on small ones. Check on both.
Where to start
Measure the bounce with the free LUFS checker. If you want a streaming version of a lo-fi track, a free AI mastering pass can bring it to a target level, and you can keep your original level as the second version. Compare the two by ear at matched loudness, not only by the meter.
For background on the sound of older formats and why some producers want a softer, warmer master, read the vintage sound of vinyl, tape and cassette in lo-fi.
FAQ
What LUFS should a lo-fi master be?
There is no single answer for lo-fi. For streaming, −14 LUFS is the common reference, and a lo-fi master can sit a little below it. In our small sample, the median after mastering was −15.9 LUFS with a true peak of −2.2 dBTP.
Is 110 tracks enough to trust these numbers?
It is enough to describe what the engine did for those tracks, and it is a useful starting point. It is not enough to set a rule for every lo-fi release, and the spread between the quietest and loudest tracks is wide. Measure your own file and decide by listening.
Why does my lo-fi master sound quieter than my other songs?
Check the integrated loudness of both files with the same meter. If the lo-fi track is a few LU lower, it will sound quieter in a playlist, and that difference is easy to hear. Whether to raise it is a creative choice, but make it on purpose, and check the noise floor when you do.
Measure your lo-fi track before you release it
The LUFS checker is free and needs no account. Measure the bounce first, then decide whether it needs a master.
Master a track free