BLOG

Distortion and clipping in AI songs: how to find it and fix it

How crackle and clipping show up in Suno and Udio exports, how to find clipped peaks with a free check, when a de-clipper helps, and when it cannot repair the damage.

A loud hit in an AI song can crackle. The drum transient sounds harsh, or the vocal turns rough on the loudest words. Often the cause is clipping. The waveform was pushed past the digital ceiling, and its tops were chopped flat. This article shows how to find clipping in an AI export, how a de-clipper repairs it, and when the damage is too heavy to repair.

What clipping sounds like

Clipping flattens the peaks of a waveform. When the level goes past the digital ceiling, the tops become flat shelves. The sound turns harsh, the distortion appears, and the drum hits lose their snap.

In an AI song, you often hear it as a crackle on the loudest hits, a rough edge on a shout, or a harshness that is there in the loud chorus and gone in the quiet verse. Some people call it distortion, but the two are not the same. Distortion can be a choice, such as a guitar amp. Clipping is damage that happened when the level went too high.

Not every crackle is clipping. A noisy file, a worn cable or a bad MP3 encode can also crackle. Use the check below before you decide.

Step 1: Measure the true peak

Start with the free LUFS checker. Read the true peak in dBTP. The true peak page explains why this number matters. A true peak above 0 dBTP means the file can clip when it is converted to analogue or encoded for streaming.

Measure the original, not a copy you made later. A quiet file can still clip after an MP3 encode, so the true peak is only a first sign. The clipping check is the next step.

Step 2: Run the clipping check

The de-clipper check is free, needs no account and does not keep your file. It returns three numbers.

The check looks for a pile-up of samples at one flat value. It does not need the flat tops to sit exactly at 0 dBFS. That is why it can still find clipping after a file was turned down or saved as MP3 or M4A.

The check looks only for clipping. It does not judge the mix or the loudness, so keep your own notes on those.

Step 3: Decide what the result means

How the de-clipper repairs a clipped peak

When the check finds clipping on the input, the lab rebuilds each short clipped peak from the sound on either side of it. The peak returns towards the shape it had before it was cut, and it never goes below the clip level. The repair runs as part of mastering, so you do not switch it on separately.

Long flat stretches are left alone. Rebuilding them risks clicks, so the tool does not try. The audio restoration page says the same: moderate clipping is repaired automatically when a track needs it, while heavy clipping, where the waveform is flat for long stretches, is only softened.

What repair cannot do

Information that clipping has destroyed cannot be fully recovered. The repair brings back the shape of short clipped peaks and reduces the distortion they cause. It is not a way to undo a crushed mix. If the whole chorus is flat, the best fix is a new file with a lower level, or a new take.

The steps that work

  1. Measure the export. Check the true peak with the LUFS checker, and write it down.
  2. Run the clipping check. Note the spots and the share.
  3. Lower the level if you can. If the export was made too hot, a new export at a lower level gives the repair more room.
  4. Master the file. The repair runs as part of mastering when clipping is found on the input. Keep the target at −14 LUFS. A louder target can push the restored peaks into clipping again.
  5. Check the true peak after the master. It should be at or below −1 dBTP. The how to fix clipped audio guide shows the same checks in more detail.
  6. Listen to the hits. Compare the repaired file with the original on the loudest drum hits. The crackle should be gone, and the hits should keep their snap.

Where clipping comes from in AI songs

Generated exports often arrive already clipped. The Suno mastering page explains that peaks close to 0 dBFS can distort after streaming encoders convert the file. A hot export is more likely to clip, and a clip is more likely to show up on a loud chorus.

Your own mix can also clip. If you add a vocal, a loop or a sound effect over an AI track, the sum can go over the ceiling. Check the final file, not only the AI export.

What to avoid

A quick check before release

  1. Measure the true peak and run the clipping check.
  2. Decide: a few spots can be repaired, a flat chorus needs a new take.
  3. Master to −14 LUFS, and keep the true peak at or below −1 dBTP.
  4. Listen to the loudest hits on headphones and a phone speaker.

FAQ

Is clipping in an AI song the same as distortion?

No. Distortion can be a sound you choose, such as a guitar amp. Clipping is damage from a level that went past the digital ceiling. The result is harsh and flat at the tops of the waves, and it cannot be undone by turning the song down afterwards.

Does a de-clipper always help?

No. It helps with short clipped peaks, such as hits on the drums or a loud word. It can only soften long flat sections. If a whole chorus is clipped, a new take or a lower-level export works better.

Do I need to lower the loudness after de-clipping?

Keep the target at −14 LUFS for streaming. A louder target can push the restored peaks back into clipping. Check the true peak after the master, and keep it at or below −1 dBTP.

Check your export for clipping

The clipping check is free, needs no account and does not keep your file. Run it before you master the song.

Master a track free