Classical and jazz mastering loudness: dynamics first
Classical and jazz uploads are quieter and far more dynamic than pop genres. Median LUFS, true peak and the wide quiet end of the range, from 2,746 tracks, and how to keep the dynamics when you master.
Topic: Mastering loudness by genre
Classical and jazz recordings are often the quietest files a mastering service receives, and their loudness is part of the music. A pianissimo passage should sound soft, and a sudden forte should sound sudden. If you are looking for the right LUFS for a classical or jazz release, this article gives the numbers first and then a way to keep the dynamics while you master. The figures are numbers from 2,746 tracks processed by the mastering engine behind Echoteka in the last six months (aggregate, no personal data): 1,035 classical tracks and 1,711 jazz tracks.
What the numbers show
| Reading | Classical, 1,035 tracks | Jazz, 1,711 tracks |
|---|---|---|
| Median loudness before mastering | −18.7 LUFS | −14.7 LUFS |
| Middle 80% of uploads (10th to 90th percentile) | −29.9 to −13.8 LUFS | −18.8 to −12.3 LUFS |
| Uploads louder than −10 LUFS before mastering | 3% | 4% |
| Median loudness after mastering | −15.9 LUFS | −14.1 LUFS |
| Median true peak after mastering | −1.3 dBTP | −1.3 dBTP |
The first thing to notice is the spread. Classical uploads run from very quiet to moderately loud, with the quiet end reaching −29.9 LUFS for one upload in ten. That is a wide range, and it reflects a genre that depends on contrast. Jazz is narrower, but still quieter than pop genres, with only 4% of uploads louder than −10 LUFS.
After mastering, the medians are −15.9 LUFS for classical and −14.1 LUFS for jazz. Classical rises by about 2.8 LU, which is a modest change for a genre with so much range. Jazz moves very little. Both finish with a true peak of −1.3 dBTP, which leaves more margin than the pop genres.
These are medians of two separate sets of measurements, before and after. They describe the level each genre arrives at and leaves with. They are not the change for any single recording.
To place your own recording against these figures, measure it with the same meter and read the loudness range along with the integrated loudness. For classical, a reading between −22 and −15 LUFS is in the middle of the spread, and a master near the median of −15.9 LUFS is a light change. A reading quieter than −29.9 LUFS is in the bottom tenth, so check the noise floor before any gain change. For jazz, a reading between −17 and −13 LUFS is in the middle of the range, and a master near −14 LUFS is a small move. A jazz reading louder than −10 LUFS is unusual, since only 4% of the sample sat there before mastering, and it is worth checking whether the mix is too hot or the file was already limited. In both genres, the loudness range is the number that tells you the most about whether the contrast survived.
What the targets mean for these genres
Spotify publishes a loudness target of −14 LUFS for integrated loudness. A classical master at −15.9 LUFS is about 2 LU below that reference. On a platform that turns loud tracks down and does not raise quiet ones, a classical album will play at its own level, and that is usually the intent. Check how each service you use handles quiet tracks, because some behave differently.
The true peak target is at or below −1 dBTP. Classical and jazz recordings often have large peaks from brass, percussion and piano attacks. The margin is still needed, but the job is to control the peaks without flattening the music around them.
The main point for these genres is that a loud master is not the goal. Integrated loudness describes the whole file, and a recording with a wide range will have a lower integrated number even when it is well made. Forcing it to −14 LUFS usually means compressing the quiet passages up and the loud peaks down, and that is the change you hear as a loss of life.
Checks before you master a classical or jazz recording
- Measure the loudness range, not only the integrated loudness. Read the loudness range (LRA) along with integrated loudness and true peak. A wide LRA is the sign that the recording still has its dynamics.
- Find the loudest peak and the quietest passage. Note where they are. If the loudest peak is a single brass or percussion hit, a small limiter adjustment may be enough. If the whole piece is loud, the mix is the problem, not the master.
- Listen to a quiet passage at the streaming level. Turn up the file to a reference level and check the noise floor. Room noise, breath and hum become audible when a quiet passage is raised.
- Compare with a reference recording at matched level. Use a recording you trust, and listen at the same integrated loudness. This shows whether your recording keeps its contrast.
- Check on the listening device. A classical recording that sounds right on studio monitors may lose its quiet detail on a phone speaker. Check on both.
Common mistakes in classical and jazz mastering
- Chasing −14 LUFS on a quiet recording. A recording at −18 LUFS is not broken. Raising it to the streaming reference often costs the contrast that made it worth releasing.
- Compressing the whole file. Heavy compression brings the quiet passages up and the loud passages down, and the piece loses its shape. If you need control, use gentle, slow settings and check the LRA.
- Raising the noise floor. A quiet passage raised by a large gain change will show room noise and hum. Fix the noise in the recording before you master.
- Ignoring true peak on loud passages. A recording can be quiet for most of its length and still have peaks that overshoot after encoding. Measure the final file, not only the master in your DAW.
Where to start
Measure the file with the free LUFS checker. It shows integrated loudness, true peak and loudness range, which are the three readings this article uses. If the recording is quiet but clean, you may only need a light master and a check of the true peak. A free AI mastering pass can help with a recording that needs a streaming level, and the comparison with your original is a good way to decide which version to release.
For more on how to read those numbers, see how to read a LUFS meter.
FAQ
What LUFS should a classical master be?
There is no single target that fits every recording. Many classical releases sit well below −14 LUFS, and that is often right for the music. In our data, the classical median after mastering was −15.9 LUFS, with a true peak of −1.3 dBTP.
Should a jazz track be mastered to −14 LUFS?
For streaming, −14 LUFS is a common reference and the jazz median after mastering was −14.1 LUFS. Jazz tends to sit close to that level, but check the loudness range too, because a loud, flat master can lose the swing and the space between instruments.
Does a quiet master mean my classical album will sound too quiet on streaming?
Not necessarily. Listeners set the volume on their own devices, and a quiet album with wide dynamics sounds right when played at its own level. If the album sits much quieter than the rest of a playlist, that is a choice you can make on purpose. Measure the file, listen at matched level, and decide with the contrast of the music in mind.
Measure your classical or jazz recording before you release it
The LUFS checker is free and needs no account. Measure the file first, then decide whether it needs a master.
Master a track free